Making your own picks is a genuine part of the hobby — plenty of competition pickers use tools they cut themselves, and the material that matters costs nothing. But most homemade picks fail for one reason: the wrong steel. This guide covers which materials work, how to cut and finish a hook, how to make a tension wrench that does not flex, and the honest answer on 3D printed picks.
What a lock pick actually has to be
Before cutting anything, the specification, because it explains every success and failure below. A working pick is:
- 0.5–0.6 mm thick. Thinner flexes and tells you nothing; thicker will not pass the warding in a European paracentric keyway.
- Flat in cross-section. Round wire rolls in the keyway and transmits almost no feedback — the reason a bobby pin is such a poor pick.
- Spring steel, hardened and tempered. It must bend slightly and snap back without taking a set. Soft steel deforms after a few pins and your carefully cut geometry is gone.
- Smooth and deburred. A sharp edge catches on the warding and on the pins, and every snag reads as false feedback.
The short version: the geometry is easy and the steel is everything. Spring steel from a windscreen wiper insert or a hacksaw blade makes a pick that genuinely works; mild steel, aluminium, brass and filament do not, no matter how good the shape is.
The best materials for homemade lock picks
Windscreen wiper inserts (the classic, and the best)
The two thin steel strips inside a wiper blade are flat, roughly 0.6 mm, and already hardened spring steel. They are, in material terms, almost exactly what a commercial pick is made of — which is why they have been the hobby's standard scrap source for decades. An old blade from any garage gives you several picks. They cut with a rotary tool or careful filing, and need no heat treatment.
Hacksaw blades (good, with one warning)
Bimetal hacksaw blades are hardened spring steel, cheap and exactly the right thickness. Grind the teeth off completely and work the blade cold — if it turns blue you have ruined the temper at that spot and it will snap. Dip it in water every few seconds. A good blade yields three or four picks.
Street sweeper bristles (the classic American answer)
The flat steel bristles that fall off road sweepers are excellent spring steel, famously the original material for Bogota rakes. They are also rarer in Europe than Reddit suggests. If you find one, keep it.
Feeler gauges, clock springs, tape measure blades
All hardened flat spring steel in usable thicknesses. A cheap feeler gauge set is the most convenient of the three, since it comes pre-sorted by thickness — pick the 0.6 mm leaf and work from that. A steel tape measure blade is slightly thin at 0.5 mm but perfectly usable and bends nicely for rakes.
What does not work
- Paperclips and bobby pins. Round, soft, and they bend before the pin lifts. Fine for a wafer lock in a cabinet, hopeless on a pin tumbler.
- Mild steel strip and sheet metal. Correct shape, no spring. It takes a permanent set within a session.
- Brass, aluminium, zip ties, plastic. No.
- Knife blades, screwdrivers, allen keys. Too thick for any keyway worth picking, and dangerous to force.
What a set of commercial picks gets you instead
How to make a lock pick, step by step
- Pick your blank. A wiper insert or a de-toothed hacksaw blade, 0.5–0.6 mm, cut to about 10 cm.
- Mark the profile. Trace a real pick if you own one, or print a template at 1:1. A short hook is the one to make first: a 2–3 mm tip, square-ish, rising gently from the shaft.
- Cut the rough shape with a rotary tool cutting disc or a file. Go slowly and keep the steel cool — colour change means lost temper.
- Shape the tip. This is the part that matters. The hook's top surface lifts the pin, so it wants to be flat and parallel to the shaft, not angled.
- Smooth every edge. Fine file, then 400 then 800 grit paper. Run the pick along your fingertip: if it catches anywhere, the lock will catch too.
- Add a handle. Heat-shrink tubing, a wrap of tape, or two strips of plastic epoxied either side. A slim handle is better than a fat ergonomic one — you are reading vibrations through it.
Expect the first two attempts to be unusable and the third to be genuinely decent. The profile you will make best is the one you use most: start with a short hook, then a snake rake, which is far more forgiving to cut than a hook because the curve does not need precision.
How to make a tension wrench that actually works
This matters more than the pick, because tension is roughly 80 % of picking and a flexing wrench is the number one reason homemade kits fail.
- Cut a strip 3–4 mm wide from the thickest flat spring steel you have — 0.9 mm to 1.2 mm is right here; stiffer than a pick, deliberately.
- Bend 8–10 mm at the end to 90°, in a vise, with a sharp corner rather than a curve.
- Keep the short leg flat and parallel. If it twists, it will roll in the keyway and your tension will jump around.
- Deburr the end so it does not bite into the plug.
If you only buy one thing rather than making it, buy the wrench. A set of double-ended wrenches costs very little and removes the variable that makes beginners think they cannot pick.
Are 3D printed lock picks any good?
Short answer: no, and the reason is structural rather than a question of print quality.
A pick works by transmitting a fraction of a millimetre of movement from a pin, through the tool, to your fingers, while resisting a force concentrated on a 2 mm tip. PLA, PETG and even nylon at 0.6 mm thick have a tiny fraction of spring steel's stiffness and no elastic snap-back. A printed pick flexes instead of lifting, the layer lines catch on the warding, and the tip shears off — often inside the keyway, which is the real risk: you have now jammed a plastic fragment into the lock.
Where 3D printing genuinely helps the hobby:
- Handles for picks you cut from steel — printed grips are excellent, and you can size them to your hand.
- Cylinder holders and vises for practice cylinders, which is one of the best quality-of-life upgrades there is.
- Pin trays and cases for re-pinning.
- Teaching models — an oversized printed pin tumbler cutaway is a brilliant demonstration piece, though an actual transparent lock costs less than the filament.

The honest comparison: a session with a rotary tool and a wiper blade gets you one usable hook and one wrench. Fifteen hardened stainless picks, two real tension wrenches and — in Set 2 — a transparent practice lock cost less than the cutting discs. Make picks because the craft appeals to you, not because it is the cheaper route to picking locks.
See the productIs it legal to make your own lock picks?
In most of Europe, making a pick is treated exactly like owning one: the tool is not the offence, using it on someone else's lock is. France, Belgium, Germany, Austria, the Netherlands, Czechia and the Nordic countries regulate the act, not the object. Finland requires an acceptable reason for possessing burglary tools. The UK restricts carrying them in public under "going equipped". Poland is the exception and it names manufacture explicitly: art. 129 of the Code of Petty Offences penalises making, possessing or acquiring picks unless your profession requires them. Country detail is on our legality page.
And the hobby rule that keeps all of this uncontroversial: only pick locks you own, and never a lock in use. A homemade pick is a fine thing to test on a practice lock and a terrible thing to test on a door.
Should you make picks or buy them?
| Homemade | Commercial | |
|---|---|---|
| Cost | Free scrap, but cutting discs and a rotary tool | Under 30 € for a full starter kit |
| Material | Wiper insert or hacksaw = genuinely correct steel | Hardened stainless, 0.5–0.6 mm, consistent |
| Finish | Needs patient deburring to feel right | Deburred and polished |
| Variety | One or two profiles realistically | Hooks, half diamonds, rakes, deep hooks |
| Tension wrench | The hard part — most homemade ones flex | Rigid, multiple widths |
| Why do it | The craft, custom profiles, no shipping | Learning to pick, today |
The pickers who make their own tools are mostly people who already pick well and want a profile nobody sells. If your goal is to open your first lock this week, buy a beginner set and a practice lock, and keep the wiper blade for later — it is a much better project once you know what a good hook feels like.
Frequently asked questions
What is the best material to make lock picks from?
Windscreen wiper inserts — the flat steel strips inside a wiper blade are already hardened spring steel at roughly 0.6 mm, which is almost exactly commercial pick material. Bimetal hacksaw blades, feeler gauges, clock springs and street sweeper bristles all work too. Mild steel, brass, aluminium and paperclips do not.
How do you make a lock pick at home?
Cut a 10 cm blank from flat spring steel 0.5–0.6 mm thick, mark a short hook profile, cut it with a rotary tool or file while keeping the steel cool so you do not lose the temper, shape the tip flat and parallel to the shaft, then smooth every edge with fine file and 400–800 grit paper and add a slim handle.
Are 3D printed lock picks any good?
No. Plastic at pick thickness has a tiny fraction of spring steel's stiffness, so it flexes instead of lifting pins, the layer lines snag on the keyway warding, and the tip can shear off inside the lock. 3D printing is genuinely useful for pick handles, cylinder holders and pin trays, not for the picks themselves.
Can you make a tension wrench at home?
Yes, and it is the more important piece. Cut a 3–4 mm wide strip from thicker spring steel — 0.9 to 1.2 mm — and bend 8–10 mm to a sharp 90° in a vise, keeping the short leg flat. If it twists or flexes it will roll in the keyway and your tension will be useless.
Is making lock picks illegal?
In most of Europe making a pick is treated like owning one: legal, with the offence being use on a lock that is not yours. Finland requires an acceptable reason for possession, the UK restricts carrying in public, and Poland explicitly penalises manufacture, possession and acquisition under art. 129 of the Code of Petty Offences unless your profession requires them.
Is it cheaper to make lock picks than buy them?
Not really, once you count cutting discs, abrasives and the hours. A full beginner kit with a practice lock costs under 30 €, and a session of filing typically yields one usable hook. Make picks because the craft interests you or because you want a profile nobody sells.
Next step: test whatever you cut on a lock that shows you the pins — see which practice lock to buy next — and get the technique right in how to pick a lock for beginners.
Beginner Lock Pick Kit – 15 Picks, Pouch, Optional Transparent Padlock
Lock Pick Set in Leather Zip Case – 10 or 24 Picks
Tension Wrench Set – 7 Double-Head Tension Tools