Guide

How to Pick a Lock: Step-by-Step Tutorial for Your First Open

Eight numbered steps, a video of the hand movements, and a troubleshooting table for every wrong sensation. The practical tutorial to get your first lock open tonight.

Updated 25 October 2026 · Technique · 10 min read

This is the do-it-now tutorial: eight numbered steps, the exact hand movements, and a table of every wrong sensation and what it means. If you want the theory first — how a pin tumbler works, why locks are pickable at all, a 30-day plan — read how to pick a lock for beginners instead. If you have a lock in one hand and tools in the other, start at step one.

What you need: a lock you own, a tension wrench, a hook and a rake.
Time to first open: under 15 minutes on a cheap or transparent padlock, by raking. One evening to a week for your first single pin pick.
Difficulty: white belt. No unusual hands required — the only variable that matters is how light your tension is.

Watch it once before you start

Lock picking is a feedback skill, which makes it hard to learn from text alone and easy to learn from thirty seconds of watching. The clip below shows the two-tool grip and the scrubbing motion on an improvised setup:

Demonstration: How to Pick a Lock with a Bobby Pin, by wikiHow on YouTube. We did not make this video and we are not affiliated with wikiHow — it is here because thirty seconds of watching two hands work shows the grip and the scrubbing motion better than any photograph. The written steps below are ours, and they go further than the video does on the part that decides everything: tension.

Two things the video does not have time to say, and they are the two things that decide whether your lock opens:

  • Tension is not a constant. You will see a hand holding a bent pin at the bottom of the keyway. What you cannot see is that the pressure is being varied, and that is the whole trick. Step 5 covers it.
  • Hairpins are the hard way. The method is genuine, the tool is not: soft round wire bends instead of lifting, so you work blind. A beginner set with a clear lock costs less than a pizza and removes that handicap entirely. Full honest comparison in picking a lock with a bobby pin.

Before step one: the two rules

  1. Only pick locks you own, or have explicit permission to pick.
  2. Never pick a lock that is in use — not your own front door, not a padlock holding something shut.

These are not legal boilerplate, they are the reason the hobby is legal in nearly all of Europe. Picking also burnishes pins slightly, so a lock you depend on is the wrong lock to learn on. Country-by-country rules are on our legality page: the UK restricts carrying picks in public, Finland requires an acceptable reason to possess them, and Poland restricts possession itself under art. 129 of the Code of Petty Offences.

Set yourself up properly too. Sit at a table. Hold the lock in your non-dominant hand with the keyway facing you, or clamp it. Rest both elbows. Picking is a fine-motor skill and fine-motor skills fall apart when your arms are in the air.

How to pick a lock: the eight steps

Step 1 — Work out which way the lock turns

Insert your tension wrench into the keyway and turn gently each way. One direction has a little give before it stops; that is the direction the key turns, and the direction you will apply tension. On a padlock it is almost always clockwise. Get this wrong and nothing you do afterwards can work.

Step 2 — Seat the tension wrench

Slide the short leg of the wrench into the bottom of the keyway, as far out of the way as it will go, and leave the long leg resting under your index finger. It should sit firmly. If it rattles, use a wider one; if it bends under your finger, use a thicker one. A wrench that flexes is the number one reason beginners conclude they cannot do this — see the tension wrench guide.

Step 3 — Apply the lightest tension you can hold

The weight of a fingertip resting on the wrench. Touchscreen pressure, not screwdriver pressure. Beginners apply three to ten times too much, which crushes every pin against the core so nothing lifts and the lock feels like a solid lump of brass. If in doubt, use less.

Step 4 — Rake it open (your first win)

Take the snake rake. Slide it all the way to the back of the keyway, teeth up, touching the pins. Now scrub it in and out — three or four strokes a second, not frantic — while rocking the tip up and down.

On a cheap or transparent padlock this opens within a few passes. That is a real open and it counts: raking exploits the same manufacturing tolerances single pin picking does, it is simply blind. Full detail and the other rake profiles are in how to rake a lock.

Step 5 — Vary the tension while you scrub

This is the step that separates a rake that works from a rake that does nothing, and it is the step almost everyone skips. Pulse your finger pressure as the rake moves: on, almost off, on. Raking works because pins bounce past the shear line and get caught there by the edge of the turning core — and the core can only keep catching them if it keeps micro-rotating. Constant tension freezes everything.

If twenty seconds of this does nothing, release everything completely, let the pins drop, and go again lighter. Resetting costs two seconds. Stubbornness costs an evening.

Step 6 — Switch to the hook and find the binding pin

Now the real skill. Keep the same fingertip tension, swap the rake for the short hook, and slide it to the back pin. Push each pin up gently and let it drop. Most feel springy. One feels stiff and does not want to move. That is the binding pin — the one whose chamber was drilled a few hundredths of a millimetre off line, which is why locks are pickable at all.

Pins never bind in order. Pin 1, pin 2, pin 3 is not a method; sweeping for the stiff one is.

Step 7 — Set it, then find the next one

Lift the binding pin slowly. You will feel a tiny click and the wrench will rotate a hair. That pin is now set — held above the shear line by the ledge of the core. Stop lifting the instant you feel the click: push further and the key pin crosses the line too (over-set), the lock jams, and no amount of work on the other pins will save it.

Sweep again. A different pin is now stiff. Lift it. Repeat. A five-pin lock is five of these, in an order the lock decides.

Step 8 — The last pin sets and the core turns

When the final pin sets, the core rotates under your wrench and the lock opens. Keep the tension on as it turns — the most common way to lose an open at the last second is relaxing your finger in surprise.

Then do it again. The goal of a first session is not one open, it is feeling one pin set cleanly, ten times.

If you own a transparent lock, do steps 6 to 8 with the acrylic body facing you. Check your feel against your eyes: when you think a pin has set, look — is the driver pin above the shear line? That single habit turns four frustrating weeks into one good evening, and it is why we put a clear lock in nearly every beginner kit.

Troubleshooting: what you feel and what it means

What you feel What it means What to do
Every pin feels identical and dead, nothing lifts Far too much tension Halve it, then halve it again
Pins lift freely and spring straight back, never a click Too little tension Increase until exactly one pin feels stiff
Raking does nothing, pass after pass Your tension is constant Pulse it: on, almost off, on
The lock suddenly feels dead after going well An over-set pin Release everything, let the pins drop, restart
The core turns a few degrees, stops hard, pushes back A false set on a spool pin Reduce tension almost to zero, keep lifting, let the wrench rotate back
Several clicks per pin, none of them real Serrated pins Steady light tension, keep lifting past the false clicks
Four pins set, the fifth will not move You are probably not reaching it Deep hook, or move the wrench to the top of the keyway
The pick will not pass into the keyway at all Pick too thick for the warding 0.5-0.6 mm picks; European keyways are paracentric

If none of those fit, the twelve usual causes are laid out in why can't I pick this lock.

Starter Lock Pick Set – 15 Picks + Transparent Padlock + Pouch – image 2
What these steps assume · €29.9Starter Lock Pick Set – 15 Picks + Transparent Padlock + Pouch

This tutorial is written around exactly what is in this box: a short hook, a snake rake, two tension wrenches that do not flex, and the transparent practice padlock that lets you check your feel against your eyes. If you are following these steps with a bent hairpin, you are doing the hardest possible version of step 3.

See the product

Your first fifteen minutes, timed

  1. 0-2 min. Insert the key in your practice lock, watch the pins line up, pull it out, watch them drop. Do it five times. This is not a warm-up, it is the mental model.
  2. 2-4 min. Steps 1 to 3. Find the turning direction, seat the wrench, learn what fingertip pressure feels like.
  3. 4-10 min. Steps 4 and 5. Rake, varying tension, resetting every twenty seconds. Expect the open in this window.
  4. 10-15 min. Steps 6 to 8 with the hook, looking at the pins. Do not expect a single pin pick tonight; expect to feel one pin bind and one pin set.

Then stop. Fifteen minutes a day beats two hours on Sunday, every time — feedback skills consolidate with frequency, not duration.

Doing this tutorial with a bobby pin

Since that is what the video shows: the eight steps above are exactly the method, and they work. What changes is how much information reaches your fingers.

You need two hairpins. Straighten the first, pull off the plastic tip, and bend the last 3-5 mm up at about 30-45 degrees — that is your hook. Break the wavy side off the second, keep about 4 cm, bend 8 mm of it to 90 degrees and squeeze that short leg flat with pliers — that is your wrench, and flattening it is not optional. A round wire rolls in the keyway and your tension jumps around, which makes step 5 impossible.

Realistic expectations: a three-pin diary or luggage padlock, maybe a cheap cabinet lock. Not a 5-pin brass padlock, not a euro cylinder, and nothing with security pins. The honest version of the comparison, including a table of which locks give way, is in how to pick a lock with a bobby pin.

Once it opens: what to practise next

A first open is a white belt. The path from there is a sequence of locks, not a sequence of tools:

  • Same lock, blind. Turn the transparent body away from you and open it by feel alone. This is the step people skip and the one that matters most.
  • Real tolerances. A cutaway cylinder or a brass padlock from a drawer. Yellow belt.
  • Your first spool pin. A security-pin practice lock. This is where everyone plateaus for a month, and where watching a false set shortens that month to a week.

Which lock to buy at each level is mapped out in the belt ranking, and the reasoning behind the order is in which practice lock to buy next. Any term here you did not recognise is in the glossary.

Frequently asked questions

How do you pick a lock step by step?

Find which way the lock turns, seat a tension wrench in the bottom of the keyway, and apply about the weight of a fingertip of rotation. Scrub a rake in and out across the pins while pulsing that pressure, which opens most cheap padlocks within minutes. Then swap to a hook, sweep the pins to find the one that feels stiff, lift it until it clicks, and repeat with the next stiff pin until the core turns.

How long does it take to pick your first lock?

Under fifteen minutes by raking, on a cheap or transparent padlock with standard pins. A first single pin pick — setting the pins deliberately one at a time with a hook — takes from the same evening to about a week of fifteen-minute sessions.

How much tension do you apply when picking a lock?

Roughly the weight of one fingertip resting on the wrench: the pressure you would use on a touchscreen, not on a screwdriver. Too much jams every pin against the core so nothing lifts and the lock feels dead, and that is the single most common reason a beginner opens nothing at all.

What do you need to pick a lock?

Two tools and a lock you own: a tension wrench that does not flex, and a pick — a short hook for single pin picking, plus a rake for fast first opens. A transparent practice padlock is the fourth item and the one that actually decides how fast you learn, because you can check what your fingers felt against what the pins did.

Can you pick a lock with just one tool?

No. Something has to hold rotational force on the core while something else lifts the pins, and that is the whole mechanism. This is why every tutorial starts with two hairpins rather than one, and why the improvised tension wrench — not the improvised pick — is usually what makes the attempt fail.

Why does my lock turn slightly and then stop?

That is a false set, almost always on a spool pin: the core has rotated into the pin's narrow waist and jammed. Reduce your tension almost to nothing, keep lifting that pin, and let the wrench rotate backwards as the spool passes the shear line. Gripping harder wedges it and kills the lock.

Is it legal to pick a lock?

In nearly all of Europe, yes, for hobby use on locks you own. The UK restricts carrying picks in public, Finland requires an acceptable reason to possess them, and Poland restricts possession itself under art. 129 of the Code of Petty Offences. Only pick locks you own, and never a lock that is in use.

Next step: the theory behind every step above — the shear line, binding order and a 30-day plan — is in how to pick a lock for beginners. When your lock starts turning and stopping, read security pins explained.

Written by the Lockpit Kit teamWe pick every practice lock we list, grade it against the community belt ranking and write the guide that ships in the box. Everything here comes from that bench work and from the public sources linked in the article. Only pick locks you own — see legality by country.

Keep reading